I've designed this badge in such a way that the LEDs on the bottom side will be visible from the TOP side, Not LEDs exactly but their glow is visible through PCB as I've left an opening in the TOP solder mask area and soldered the LEDs inverted, so they would shine right through the fr4 board. Let me explain the whole built process and assembly of this badge including working in few words to keep things short here as this is just an accessory for the robot. Finally…. pop the horn and the flowers on the top of the pandacorn cake. And some of the side for decoration.. and done!! I hope you found this easy Pandacorn Cake for Beginners inspirational and that you will have a go. Remember: keep cake decorating simple. Don’t worry if you need to cheat. And just have a go!!!!! Panda Quilling project– this is something for people who would like a bit of a challenge and are into Paper Quilling. Other fun and easy Panda DIYs

Cut gold paper into a quarter circle. Roll up. Secure with tape! Done. I decuded to add a thin pink ribbon as a detail and simply wrapped that around and secured with tape. Paper Flower How To The PCB consists of an Arduino Nano connected with the L293D Motor driver IC in its proper configuration, HC01 is also connected with the Arduino Nano. The twins love an unboxing video as much as the next toddler, so I figured… why not? And today is Global Hatching Day, so it’s finally time to share what’s inside! This version is definitely not the final iteration as I still have to improve a lot of things in this bot.The twins couldn’t wait to get the eggs open. Literally. They couldn’t wait. As soon as they had those eggs in their arms, it was game over. I’m afraid they did not wait for the Global Hatching Day. To be honest, I’m glad they couldn’t wait, because I was actually quite excited to see what was inside, too. There’s something about a surprise box that turns adults into kids again, isn’t there! Jigsaw puzzles are a fun family activity that can bring people together to complete a common goal. They are great at developing memory and hand-eye coordination and can even feature favorite animals. This panda jigsaw puzzle is a smaller puzzle that will help keep the attention of kids and adults as they put all the pieces together. Finishing a puzzle is a great feeling and will build and inspire confidence in your kids. So here we go…. how we made our Pandacorn Surprise Cake (you can leave the surprise bit out and just make the pandacorn cake for ease if you wish… but the surprise bit is actually easier than baking a big cake.. more on that below!).

I **really** don’t consider myself much of a baker. But I **do** know that I am crafty (well, you would hope so, running this blog!!!), so I am always looking forward to create fun cakes for my kids, that I consider to be relatively easy.. and that I genuinely believe most bakers – whether you love baking or hating – can achieve!!! The key to a fun cake is – to keep it SIMPLE. Oh and to cheat as much as possible. Enter today’s Pandacorn Cake for Beginners!!! My daughter asked for a Panda cake for her birthday.. which, though I am not keen on working with fondant icing, I though should be relatively easy. As started thinking about it in more detail, I thought, why make an ordinary panda cake…? When you can have a PANDACORN cake. Pandacorns are a “thing” don’t you know.The same recipe, using 4 eggs, in two tins. No food coloring. It should be fine too! The Pandacorn Surprise Pinata Cake assembly Easy Pandacorn Cake– this really is a DIY Panda Cake (super easy, with a few simple cheats) plus some paper decorations to turn it into a Pandacorn. The paper decorations were SO easy to make and meant I didn’t have to faff around with edible versions – that I simply am not very good at! Ha. I made 2 batches of cake (I htink if you try and make one HUGE batch, that is where things go wrong and things don’t get mixed properly). Like I said, we have been thinking about putting a picture book like this online for a long time, to join all the sci-fi and fantasy books I have written, but we weren't sure how to go about it.We have created lots of images for merch, on Society Six, such as T-shirts featuring a pandacorn in a snowglobe.

I assembled it with solder paste dispensing process and then flash the attiny13A with the main sketch using an Arduino as ISP Programmer setup and the badge was completed. It's an Attiny13A Powered PCB badge that drives 6 Blue LEDs with help of a simple Mosfet as switch setup. DISCOVER a kingdom filled with the adorable Caterpillow critter, Nautilus critter, Pandacorn critter and more!I've used a 12V 2.6A Battery in this setup, It's not recommended to add 12V directly with Arduino's VIN port so I added AMS1117 to step down this 12V into 3.3V for Arduino and HC01 to run without any issue. Both the Rainbocorns Sequin Surprise Series 2 and the Rainbocorns Sparkle Heart Surprise are suitable for ages 3+ and are available from Smyths, The Entertainer, Argos, Asda, Tesco, and B&M from July. Panda Mini Notebooks– my “YouTube Kids” love all things notebooks.. so we had to make some Panda inspired mini notebooks from ONE SHEET of paper and (almost) no glue!! Woohoo! So the goal here was to combine two of my recent project to make a new project that is this "PANDACORN BOT" it works the same as before iteration but the only difference is the increase in height&length in the body and the addition of PANDACORN PCB in the front part.

As mentioned, we hosted a little Panda Party for my daughter’s 9th Birthday recently. We particularly loved making the rainbow pinata, smarties filled Pandacorn cake. And I created a “few short cuts” for people like “me”– basically – crafty, but NOT that good at baking. Ha!! The whole idea behind making this Micro Robot was to make multiple of these bots and make them fight. PCB and 3D Printed Base are held together with 3 Pillars, kinda like in a sandwich configuration. The battery is placed between them and on the bottom side, there are 4 Micro Gear Motors and wheels.

Comments

first would be the overall stability and alignment of motors, as you could see in the attached gifs, this robot is unable to take a straight path, this is because of misalignment of motor position. But in this project, I removed almost everything and just kept the LEDs (I didn't use 6 LEDs, just used 5) along with the mosfet and two resistors. a small amount of white fondant icing (use white paper if you don’t want to buy white for such a small amount A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | Unnamed | Licensed