To leave a gap to enable tiling down to the tray we fixed a section of batten horizontally level across each wall around an inch above the tray and then tiled up the wall. Simply drill a 57mm hole in the soil pipe, coat the inside face of the boss with silicone and clip it in place.

Once the grout has cured you can then seal up the gap between the top of eth tray and the tiles. Use a suitable silicone, in this case we used Everbuild Forever White as we find it to be really good. Next, mark the floor area inside the tray waste so that you know exactly where you need to cut the hole for the waste. As we have mentioned installing a new shower tray with the waste in the same position as the old one should minimize potentially a great deal of work. Installing or fitting a shower tray is very much dependent on the type of tray you are installing and the surface it’s being installed on. All trays are acrylic capped and constructed from a polyurethane resin mixed with filler including clay beads making them the strongest and lightest available

What finance packages do you offer?

Plumbing World is a plumbers merchant and bathroom showroom that has been trading since 1996 and has gained a vast amount of experience in dealing with individual customer requirements. New ceramic tiles above a shower tray grouted and once cured gap between shower tray and tiles filled with silicone sealant The time it takes to fit a shower tray, and enclosure will depend on the job's complexity. But typically, a qualified plumber will take 1-2 days. The work may involve dismantling and removing the old shower enclosure and tray (if there is one), preparing the floor, fitting the tray, making adjustments for low-profile shower tray installation on a solid floor if necessary, and fitting the enclosure panels. Once the tray and enclosure are installed, the walls and floor can be tiled, and the shower can be fitted. Ensuring the waste in the floor and tray lines up: ideally, buy a shower tray with a drainage hole that lines up with the position of the waste pipe on the floor. But, bear in mind that if a different tray is used or the shower enclosure is being moved to a new position, the waste pipe and plumbing will need to be adjusted before the shower tray fitting.

After removing the old tray it was found that a long term leak had caused a fair amount of damage to the walls and floor that would all need to be replaced before the new tray was installed in place. All trays have a flat underside making installation and leveling even easier Slimline: At just 40-45mm high stone resin trays are amongst the sleekest on the market The main rule of thumb when it comes to any job such as this is to keep it as simple as possible. Go with most suitable type of tray for the room space you have and go with the most straightforward method of getting the waste water from eth tray to the main drainage point. Unfortunately in some cases, this may mean a compromise in terms of appearance. Tighten it so that it is “pinch” tight e.g. tighten it as much as you can by hand and then one final turn to pinch it up and seal it. You don’t need to over tighten it! A walk-in shower is an excellent choice for a disabled shower and for those with accessibility needs. Walk-in shower tray sizes range from 700-900mm in width and 900-1800mm in length.Before replacing any sections of floor a good idea is to test the waste and make sure there are no leaks. Using a jug, fill the waste up and continue to pour water it (a second helping had would be good here). Likewise with a floating timber floor, you can almost guarantee that there will be a supporting wall or other obstacle right where your new waste needs to go!

On first inspection of the walls it was apparent that many of the tiles had come loose also so all of these were also removed. Installing a shower tray in sand and cement or concrete floor: the plumbing pipes and waste will likely be exposed above the ground, so you'll need a raised shower tray or a low-profile shower tray and a riser kit. This job involves adjusting the shower tray feet to the correct height and ensuring the tray is level. Tiling around a shower should always be done after installation so that a good seal can be created. Tiles should stop short of the tray by about 3mm allowing an expansion joint. Finally, apply a suitable shower sealant around the perimeter. To get a professional finish, tape can be used on either side of the joint. Apply the silicone and smooth with a wet finger or silicone shaping tool. Carefully remove the tape and allow the silicone to cure. Shower Tray PlinthAn essential for any shower enclosure installation, shower trays provide a waterproof platform for you to stand on comfortably while showering. Our truly comprehensive collection boasts over 200 shower tray options to ensure you find a tray that perfectly suits your space no matter how distinctive your tastes. If you’re happy with the general fitment, you then need to establish the best possible route for your waste pipe if this isn’t already in place. Attach the waste to your tray then connect this to the trap. Step 3 - Level the Tray This is caused by the tray not being installed level. The tray will have been made with a fall on the internal surface so that water will drain correctly to the waste outlet. Reinstalling so that the tray is perfectly level will solve this problem. Creaking shower tray. To find out how to fit both a raised or flat shower tray read on below. Should I install a raised or flat shower tray? Turning a low-profile shower tray into a raised one by using a shower tray riser kit is possible. This consists of adjustable legs and clip-on side covers which conceal the legs and pipe work. These covers can be removed easily as and when needed to gain access to the pipes.