With the blade to the right of the handle, it’s a little easier for right-handers, but, thanks to the well-positioned two-way release switch, left-handers will have little problem using it. What’s different about this Dremel mini circular saw is the fact it uses abrasive cutting technology. That means that the wheels are abrasive and not tooth bladed wheels like the rest. Laser guide: Though not a necessity it is useful in guiding you to cut accurately and in a straight line. We’ve tested the three main types of saws here – corded, cordless, and a mini circular saw – covering all-round useability, the accessories included, the noise when the saw is spinning freely and during a cut, and, of course, its ability to cut wood. Most circular saws offer the ability to set the cutting depth and the angle of a bevel by adjusting the saw’s angle relative to its baseplate guide. The depth of a cut will vary according to the angle – most saws will be able to cut more deeply when positioned at 90 degrees to the material, while angled cuts won’t be quite as deep.

Blade capacity: Larger blades means more power and more depth. Normally the blades used in circular saws vary between 5 ½ to 71/4 inches. Most blades around 5 3/8 inch can comfortably cut through 2 inches of lumber. But remember, the bigger the blade the heavier the saw. This Einhell TC-CS 860 has a special steady aluminium soleplate, which offers good sliding properties for a firm, constant sawing. Yet again, it contains an integrated laser which comes as a support for an accurate execution of straight cuts. This tool also features an overload cut-out. You lift a lever to adjust the cutting depth, or turn a knob to vary the cutting angle – and both have marks to ensure accuracy. It’s a touch louder than the Makita, in both its no-load performance and during cutting, but its no-load speed is only a fraction behind. For occasional use, the Mac Allister is highly impressive, especially given that appealing price tag. The best circular saws operate at the fastest speeds, measured in revolutions per minute (rpm). And the faster a circular sawblade can spin, the more control you’ll have over the cut and the cleaner it will be. You’ll generally find a correlation between the blade speed and the power rating of the tool, where bigger is almost always better.

Similar products

The big decision you’ll have to make is whether to go corded or cordless. Corded circular saws will never suffer from a flat battery, and a consistent 240V power supply delivers the kind of oomph that more powerful saws need. On the flip side, cordless saws offer ultimate portability, away from a conventional power source, and you won’t have to worry about slicing through a cable, especially if you’re working in a confined space. Key specs – Weight: 2.16kg (excluding battery); Blade diameter: 150mm; Cutting depth at 90 degrees: 45mm; Cutting depth at 45 degrees: 32mm; No-load speed: 4,700rpm However, let’s not take away its merit. Without a quality finish blade and an expert hand, a full-size circular saw tend to produce tearout when cutting thin pieces of trim or any other thin finish material. Therefore, depending on your needs, you might find out that you do need a mini circular saw after all. So, what is the best Mini Circular Saw? There’s no doubting the quality of the Makita, which goes a long way to explain the brand’s popularity among tradespeople. With the exception of the handle and motor shroud, pretty much everything here is made from metal and it feels like it could withstand an atomic blast, let alone a drop from a workbench. Base plate: It is important that the base plate be sturdy and strong to provide stability to the saw during operation.

This will depend on what you’re planning to cut and how you’ll be using the circular saw. Larger blades will cut more deeply, but they can also be unwieldy. Not all blades will fit on all saws, but you can swap between blades depending on what you’re cutting. The max depth is 28.5 mm, a lot smaller compared to its Worx counterpart. Yet again, the laser is accurate and a friend in need and the depth control is easy to adjust. If you’re working in a confined space, a mini circular saw can be indispensable and Einhell’s TC-CS is a great example. At just 2kg, it’s light and, with a handle roughly the same size as a grinder, it’s easy to hold.Just like the rest of the mini circular saws, this specific model is single-handed. It also benefits of an ergonomic design for an increased comfort and control. With its handle to the left of the blade, it’s easy to use – especially with well-placed trigger and trigger release buttons on the handle – and made short work of our test cuts. We liked the saw’s reassuring 3.8kg weight, and it delivered confidence in operation, but it may be too cumbersome for some uses. It recorded 100dB when running freely, and 108dB while cutting. Key specs – Weight: 3.37kg; Blade diameter: 165mm; Cutting depth at 90 degrees: 55mm; Cutting depth at 45 degrees: 38mm; No-load speed: 5,000rpm Due to its size and power, you don’t get any blades for metal or aluminium as it is not intended to be used on such materials. Some of us use a mini circular saw only for cutting wood while others for metal, aluminium, or other materials. It is important to highlight that this specific model comes with 6 different blades, although it is considerably cheaper.

Plus, plunge cuts are also possible thanks to its adjustable cutting depth. You also get 12 months warranty on it. It comes equipped with a battery-powered laser which projects a light along the line you wish to follow on a cut. That makes the cut far more accurate and easier.As the name suggests, the mini circular saw is a smaller version of a typical, full-size circular saw. They are lightweight and easy to handle. You can get your small jobs done by using it for paneling, molding, cabinetry any light furniture or flooring material. It’ll cut to a depth of 66mm (46mm at a 45 degree angle), and can easily be adjusted by sliding a lever to tilt the footplate, but there’s no guide, so you’ll have to make your own measurements. The bevel is better – it can be adjusted by loosening or tightening two screws, and there’s a guide to ensure accuracy. The saw comes with a parallel guide, an allen key (which stores in the saw’s handle) and, impressively, a tough, plastic carrying case. Key specs – Weight: 3.37kg; Blade diameter: 85mm; Cutting depth at 90 degrees: 23mm; Cutting depth at 45 degrees: NA; No-load speed: 6,000rpm As a rule of thumb, the more teeth a sawblade has, the neater the cut will be. However, low-powered circular saws often work best with blades which have bigger teeth. Left- or right-handed circular saws? Weighting around 1.9 kilograms, it is extremely lightweight. It features a maximum cutting depth of 23 mm.

The kit includes 1 x DSM500 Multipurpose Carbide Cutting Wheel, 3 x DSM510 Metal and Plastic Cutting Wheels, one Dust extraction, 1 x Straight Edge Guide, 1x 2×4 cutting guide, 1x welcome DVD and last, but not least, a spacious storage case. Bevel adjustment: For the correct angle required for bevel cuts the bevel should be adjustable preferably to 45 degrees.Its bevel lever allows you to change your cutting angle up to 45 degrees. Therefore, this can be considered a mini plunge circular saw, as it’s a great alternative for light plunge cuts. We like the fact that this mini circular hand-held saw comes in a smart compact kit. The tool bag is included in the delivery. Key specs – Weight: 3.8kg; Blade diameter: 190mm; Cutting depth at 90 degrees: 66mm; Cutting depth at 45 degrees: 46mm; No-load speed: 5,200rpm As you can see, it comes with three attachments that will help you explore the variety of cutting of this the Dremel DSM20.