The Intatherm safe touch thermostatic basin mixer tap, designed for both domestic and commercial applications. A new stylish design featuring Inta’s proven anti scald technology a safe touch body and a self draining spout.

There is hardly any room under the basin, less under a bath and a kitchen sink is a nightmare! Plumbers on the other hand, carry a box spanner which is a long open tube with the correct size nut shaped hole at the end. This is the one place that I save my pushfit connectors for. If it is possible I use a pushfit to connect to the tail. The larger two of these holes are for the feed pipes to be screwed in and the smaller two are where the threaded connection bars are screwed into. The Armitage Shanks Contour 21+ Single Lever Basin Mixer Tap with c opper tails is an anti-vandal unit ideal for installation within any commercial or domestic space. It comes with extended lever handle making it particularly suitable for installation in any healthcare or disabled toilet room setting. Thanks, I appreciate the input. I didn't know that monoblocs were more restrictive than single taps.

Once the tap is in the hole with the flat washer or mounting plate placed over the threaded bars, the steel washer can be slid into place also. Copper tails, which are narrower where they go through the tail, increasing to 15 mm at the pipework connection end. Less restrictive than flexis, but no as good as 15 mm pipes.

Ceramic insert (1/4 turn) taps have two ceramic discs inside, each with two diametrically opposed slots. The faces of the discs are grounds extremely flat so that they form a water tight seal. The slots each occupy just under 1/4 of the diameter of each disc, a little way in from the outside. When closed, the slots in the upper disc are covered by the unslotted portion of the lower disc, and no water flows. When open the slots of the upper and lower discs are in alignment, so water can flow through. However, the area through which the water can flow is much less than that offered by a traditional tap washer being raised off its flat seating, so flow rate is less. The image above shows the tap at the top with the connection tails at the bottom ready to receive the hot and cold feeds. The 10mm feed pipes screw into the underside of the tap and are then machined out to become 15mm copper tails ready for the connection of 15mm feeds. These threaded bars should be fitted before dropping the tap through the hole in the basin. Only do them up as tight as you can by hand. If you use pliers or grips there is a danger you will damage the thread. not when in a confined space or when the fittings end up situated side by side as when connecting to monobloc tails.If your basin is designed for a monobloc tap, it will have a single tap hole, so you don't have the option to convert to separate taps unless you change the basin.

If you're charging by the hour Seriously, installing sinks that are so thin they can't take a normal monobloc There are no obvious restrictions being caused by the connecting pipework. I don't need to get it anything like mains pressure, but just enough improvement to avoid having to fit a pump. As it is now, I just measured a measly 1.71 l/m. Yes they will work fine providing you are careful not to unscrew the tail whilst tightening the compression.

This WRAS approved product is manufactured from chrome-plated brass and has 15mm copper tails. Fitted with a 5 litre per minute flow regulator, this model offers excellent water-saving properties as well as a built-in self-draining spout to reduce the risk of bacterial growth from static water. With the washer in place the nuts can now be tightened onto the threaded bar and this is where the DIY enthusiast struggles. Use a Box Spanner Stig, the copper tails that come with the monobloc taps are usually ribbed to allow easy bending by hand, which allows you to bend them into a position where the couplers are far enough apart, to tighten without a problem. The ideal arrangement is to have two pushfit elbows to connect the tails to horizontal pipes (and then to isovalves etc). With this arrangement any future replacement can be accomplished in about 15mins. The Armitage Shanks Contour 21+ Single Lever Basin Mixer Tap with copper tails is an anti-vandal unit ideal for installation within any commercial or domestic space. It comes with extended lever handle making it particularly suitable for installation in any healthcare or disabled toilet room setting.