TP-Link TL-WPA8630P Dual Band Gigabit AC1350 Add-On Powerline Adapter, Range Extender, WiFi Extender/Booster, Data Transfer Speed Up To 1300 Mbps, Extra Power Socket, No Configuration Required
FREE Shipping
TP-Link TL-WPA8630P Dual Band Gigabit AC1350 Add-On Powerline Adapter, Range Extender, WiFi Extender/Booster, Data Transfer Speed Up To 1300 Mbps, Extra Power Socket, No Configuration Required
- Brand: Unbranded
Description
After installing OpenWrt, the Powerline interface should just work OK out of the box with its last configuration. No firmware loading or configuration is necessary. ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=20 from ath10k/QCA9888/hw2.0/board-2.bin EasyMesh-Compatible - Flexibly creates a Mesh network by connecting to an EasyMesh-compatible router for seamless whole-home coverage bin_filename=QCA9888/hw.2/athwlan.bin swap_filename=/lib/firmware/QCA9888/hw.2/athwlan.codeswap.bin
linux_params_init 268 line = console=ttyS0,115200 root=31:03 rootfstype=squashfs init=/sbin/init board=AP152 mtdparts=spi0.0:128k(factory-uboot),128k(u-boot),1024k(uImage),6784k(rootfs),64k(mib0),64k(ART) How can I copy the wireless setting from the front router using Powerline ac Wi-Fi Kit by Wi-Fi Clone button? 07-20-2021 80635 ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 These instructions will clear a flag in the extra-para flash memory partition that will enable the OEM recovery HTTP server built into U-Boot. The location of this partition in flash memory is specific to your device version, so you must carefully follow #choosing_the_right_firmware to chose the correct instructions here:
To Upgrade
It's recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade. Plug and Play - Set up your powerline network and start enjoying fast, seamless wired/wireless connections in minutes
For devices matching the tplink_tl-wpa8630p-v2-int and tplink_tl-wpa8630p-v2.0-eu firmwares with extra-para located at 0x632100: The QCA7550 PLC stores its firmware and configuration in its own dedicated 1Mb flash and runs independently of the router. (This is different than some other Powerline routers (e.g. d-link_covr-p2500_a1), where on every boot the PLC reads its firmware over Ethernet from the plchost daemon running on the router OS). arg 6: mtdparts=spi0.0:128k(factory-uboot),128k(u-boot),1024k(uImage),6784k(rootfs),64k(mib0),64k(ART) Once the firmware has been flashed, you will see this on the console and the device will reboot into the OEM firmware:
Powerline adapters may cause intermittent connection of DSL modem router in a few rare cases 03-24-2022 70821
arcs_cmdline= console=ttyS0,115200 root=31:03 rootfstype=squashfs init=/sbin/init board=AP152 mtdparts=spi0.0:128k(factory-uboot),128k(u-boot),1024k(uImage),6784k(rootfs),64k(mib0),64k(ART) mem=128M How to add an extra Powerline AC extender to the existing Powerline AC wireless network by Pair button 06-28-2022 95303 To avoid wireless disconnect issue during firmware upgrade process, it's recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device. It is easy to overwrite your U-Boot loader using this console by writing to different memory locations, so it is recommended you only use these tried and tested instructions. MIMO - Establishes multiple simultaneous connections for you to enjoy higher powerline speeds and greater stability
2X2 MIMO met Beamforming
Linux version 3.3.8 (tomcat@buildserver) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Wed Oct 18 09:58:10 CST 2017 Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. ( Normally Vx.0=Vx.6/Vx.8 (eg:V1.0=V1.6/V1.8); Vx.x0=Vx.x6/Vx.x8 (eg:V1.20=V1.26/V1.28) TL-WPA8630P login: [ 13.320000] ath_hal: 0.9.17.1 (AR9380, REGOPS_FUNC, PRIVATE_DIAG, WRITE_EEPROM, 11D) LuCI does not have any native Powerline PLC management, but you can cover the basics using luci-app-commands:
How to set a new Powerline Network Name to secure your whole Powerline network using the tpPLC Utility on Windows 06-28-2022 116096Kernel command line: console=ttyS0,115200 root=31:03 rootfstype=squashfs init=/sbin/init board=AP152 mtdparts=spi0.0:128k(factory-uboot),128k(u-boot),1024k(uImage),6784k(rootfs),64k(mib0),64k(ART) mem=128M How to set up a new secure wireless network using Powerline ac Wi-Fi Kit by Pair button 06-28-2022 87202 How to add an extra Powerline adapter to the existing Powerline network by adding the powerline key on tpPLC Utility(new designed blue UI) 06-28-2022 75778 Now that you know more about the unboxing experience, let's see what you get in terms of hardware specifications. Hardware specifications and design
- Fruugo ID: 258392218-563234582
- EAN: 764486781913
-
Sold by: Fruugo